1. _________ is/are routed protocol.
A. RIP
B. OSPF
C. Both RIP and OSPF
D. Neither RIP nor OSPF
Ans
2. a (an) ___________ routed between different autonomous system.
A. BGP
B. EGP
C. IPP
D. IGP
Ans
3. A Routing protocol will use a (n) _______________ to determine which path is the best path.
A. Administrative Distance
B. Metric
C. Hop Count
D. Cost
Ans
4. Which type of Routing Protocol uses the shortest path first algorithm?
A. Distance Vector
B. Link state
C. Hybrid
Ans
5. Which is an example of a hybrid protocol?
A. IS-IS
B. OSPF
C. RIPv1
D. EIGRP
Ans
6. What command will prevent RIP routing updates from exiting an interface but will still allow the interface to receive RIP route updates?
A. Router(config-if)#no routing
B. Router(config-if)#passive-interface
C. Router(config-router)#passive-interface s0
D. Router(config-router)#no routing updates
Ans
7. Which of the following is true about route poisoning?
A. It sends back the protocol received from a router as a poison pill, which stops the regular updates.
B. It is information received from a router that can’t be sent back to the originating router.
C. It prevents regular update messages from reinstating a route that has just come up.
D. It describes when a router sets the metric for a downed link to infinity.
Ans
8. If your routing table has a static, a RIP, and an EIGRP route to the same network, which route will be used to route packets by default?
A. Any available route
B. RIP route
C. Static route
D. EIGRP route
E. They will all load-balance.
Ans
9. What does RIPv2 use to prevent routing loops? (Choose two.)
A. CIDR
B. Split horizon
C. Authentication
D. Classless masking
E. Holddown timers
Ans
10. Which of the following protocols support VLSM, summarization, and discontiguous networking? (Choose three.)
A. RIPv1
B. IGRP
C. EIGRP
D. OSPF
E. RIPv2
Ans
11. The ____________ Metric measures traffic over the network
A. Hops
B. Loads
C. Delay
D. Bandwidth
Ans
12. The ________ metric specifies the amount of data that can travel over the network segment
A. Hops
B. Loads
C. Delay
D. Bandwidth
Ans
13. The network administrator or techxio company has the ability to decide the optimum route based on the hop metric. Which algorithm is the protocol implement?
A. SPF
B. RIP
C. EIGRP
D. OSPF
Ans
14. _____________ Uses the Defusing Update Algorithm to update the routing table.
A. RIP
B. OSPF
C. IGRP
D. EIGRP
Ans
15. The ______________ is a link state routing protocol, used to handle routing for internet protocol traffic.
A. RIPv1
B. OSPF
C. EIGRP
D. BGP
Ans
16. The OSPF maintains a two-layer hierarchy consisting of ___________ and ____________
A. Common Area
B. Backbone Area
C. Totally Stubby Area
D. Off-Backbone Area
Ans
17. Which two of the following are true regarding the distance-vector and link-state routing protocols?
A. Link state sends its complete routing table out all active interfaces at periodic time intervals.
B. Distance vector sends its complete routing table out all active interfaces at periodic time intervals.
C. Link state sends updates containing the state of its own links to all routers in the internetwork.
D. Distance vector sends updates containing the state of its own links to all routers in the internetwork.
Ans
18. What metric does RIPv2 use to find the best path to a remote network?
A. Hop count
B. MTU
C. Cumulative interface delay
D. Load
E. Path bandwidth value
Ans
19. OSPF Uses ______________ as a Metric.
A. Bandwidth
B. Delay
C. Cost
D. Hop Count
Ans
20. RIP Generates routing updates every _________ Second
A. 15
B. 30
C. 60
D. 90
Ans
No comments:
Post a Comment